Débitmètre anticorrosion à prix réduit gaz humide de laboratoire LMF-1 débitmètre de haute précision 2 L

LMF-1 2L Laboratory Anti-Corrosion Wet Flowmeter Wet Gas Flowmeter

• The instrument is made of SUS304 stainless steel and can measure various corrosive gases.

• Large screen reading, high accuracy, small error.

• There is a level at the top to ensure the smooth placement of the instrument.

• The bottom is a telescopic foot for adjusting the height, which can be adjusted at any time.

• Wide range of application, widely used in laboratory, industrial testing and other fields.

2. Open the sealing nut of the water level controller and pull out the wool rope inside;

3. Into the jack of the thermometer or pressure gauge, inject distilled water into the instrument, and stop the injection of distilled water when the distilled water flows out of the water level controller hole. When the excess distilled water flows clean along the wool rope from the water level controller hole (about 5min without dropping a drop), Then pull the wool rope back into the water level controller, and tighten the sealing nut;

4. Install the thermometer and pressure gauge (each cell is 10pa);

5. Connect the good gas path according to the inlet and outlet direction, and seal it;

6. Open the air valve, the instrument is pre-run, and the reading can be carried out after a few weeks of pre-run.

1. In use, it is necessary to often pay attention to the water level in the instrument to remain stable, otherwise it will affect the measurement accuracy.

2. In use, the temperature should be maintained between 15-25 °C, the temperature is the same as room temperature, and the temperature difference should be less than or equal to 2°C.

3. After opening the air valve, the gas in the intake pipe enters the instrument, and the watch hand begins to rotate. When the meter continuously rotates for 5 minutes or the gas volume through the instrument is equivalent to 50 times the rotation volume, the reading can be carried out.

4. When the pressure of the measured gas exceeds the normal pressure value of 1 to 6 times (1-6kpa), the instrument can still work, at this time should be taken off the pressure gauge, with a non-porous rubber plug to plug the pressure gauge mounting hole.

5. When the flow rate of the measured gas is used within the range of rated flow to overload flow, the instrument can still work, but the measurement accuracy will be reduced at this time.

6. When the instrument is not used for a long time, the distilled water in the instrument should be discharged clean, the water discharge valve should be used first, and then the meter head down, and then the outlet pipe down, so repeated several times, in order to completely discharge the water.

7. The instrument should not be placed in the too cold indoor installation, so as to avoid internal icing.

8. Under normal use, at least once a year to check the accuracy.

Default Shipping Cost or Free Shipping Information:
▲ Default shipping cost or free shipping service is only for the customers from Canada or the lower 48 United States by Canada Post, USPS or the UPS Ground. Customers from other areas or needs other shipping ways, please contact us.
▲Buyers from Guam, Puerto Rico,Virgin Islands, American Samoa, Alaska, Hawaii, PO Boxes, APO/FPO addresses or other countries/areas, there WILL be extra shipping costs, please contact us for more detailed information.
▲Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer.

Handling Time:Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.

Sales tax / Customs duties:Any sales taxes or Customs duties are not included. If came out, they must be undertaken by the buyer.

Damage In Shipping:Email or call us First! We will work with you to get the case resolved in the fastest method.

If you are not 100% happy with your purchase, please contact Us. Please dont directly opened a request or case without informing us, or else, we will do some discounts on the warranty and other sales-services later on. Hope for your understanding.

Returns & Exchanges

Defective & Damaged Products

▲If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, its much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. Hope for your understanding.
▲ Replacement or refund of defective or damaged products can only be returned in exchange for the exact same product, or else, the purchase price will be refunded back to your original payment method.
▲If an item is received damaged, customer service must be contacted within 7 days of receiving your item. All returns require a RA (Return Authorization) number as above.